Dahle 508

Dahle 508 інструкція користувача

(3)
  • OPERATING INSTRUCTIONS FOR DAHLE PERSONAL
    TRIMMERS, MODEL NUMBERS 500, 507 AND 508
    READ THESE INSTUCTIONS BEFORE USING YOUR TRIMMER:
    Safety
    All Dahle trimmers are individually checked for correct operation before distribution.
    When using this trimmer, please adhere to regulations governing the operation of
    trimmers and ensure that all safety features are working properly.
    This machine has a rotating circular blade which is pulled longitudinally through the
    material to be cut. The blade is housed in a plastic cutting head guard for safety.
    THIS TRIMMER MUST NOT BE OPERATED IF THE CUTTING HEAD GUARD
    IS NOT IN PLACE.
    DO NOT UNDER ANY CIRCUMSTANCES TOUCH THE EDGE OF THE
    CIRCULAR BLADE WITH YOUR HAND
    Features
    The two horizontal and one vertical scale bars marked on the trimmer table area are calibrated in
    inches (1). The photographic size markings and the degrees (together with paper size markings on
    the model 500) on the table area are meant as a guide only (2). The machines are provided with a
    ground steel circular cutting blade enclosed in a cutting head (3) and an automatic clamp (4).
    Operating the trimmer
    The machine is able to cut up to 4 sheets of 20# paper in one pass. It can also cut light card, acetates
    and other thin materials. Any attempt to exceed the stated single pass capacities could result in
    damage to the machine. If you have any doubts concerning the ability of the machine to cut any
    particular material then contact our helpdesk for advice.
    The rotating circular blade is pulled longitudinally through the material to be cut. The blade housing
    is fitted to a support bar along which it runs. The machine will cut in both directions along the
    support bar axis.
    With the blade housing parked at one end of the support bar, insert the material to be cut underneath
    the clear plastic clamp (4). Push the material through until the place that you wish to cut is aligned
    with the table area cutting edge. Use the plastic moulding at the top or the bottom of the trimmer (5)
    as a guide to ensure that the material is set square to the blade before cutting. For a good quality cut,
    even with the thinnest material, it is advisable to pull the blade housing along the cutting support bar
    gently and evenly. Moving the blade housing along the support bar automatically engages the plastic
    clamp to ensure that the material is held securely in position. Pull the blade housing along the entire
    length of the cutting support bar and park it at the opposite end from which you started before
    attempting to remove the material you are cutting. The scale bars and table markings can be used to
    help achieve an accurate cut.
    Changing the blade
    The rotating circular blade on Dahle Personal Trimmers is designed to be self sharpening. However,
    depending on usage, it is likely that the blade will eventually become blunt. This can be detected by
    reduced cutting capacity and greater effort required to run the blade housing along the support bar.
    Dahle Personal Trimmers have been designed to ensure that replacement of the blade is a simple
    operation.
    The blade housing support bar (6) is fixed within the side parts of the trimmer. Take out the clip (7),
    then pull out the support bar (6) far enough for the blade housing to come off. Slide the new blade
    housing* onto the support bar ensuring that it is installed the same way round as the old one (the
    rubber wheel inside the blade housing should sit on top of the automatic plastic clamp and the
    circular rotary blade should run alongside the metal table area of the trimmer). Now slide the support
    bar (6) back in and put the clip (7) back in place.
    For technical advice concerning this product, or information concerning servicing, contact the Dahle
    Customer Service Department at 800 - 243 - 8145.
    * New cutting heads for your personal trimmer are available from Dahle.
    00507.95.0830 - 06/00 -
    http://www.monomachines.com
    http://www.monomachines.com
    5
    For More Info
    Click Here --->
Dahle 508

У вас виникло питання стосовно Dahle 508?

Кількість запитань: 0

Задайте запитання іншим користувачам Dahle 508. Надайте чіткий та вичерпний опис проблеми та свого запитання. Чим детальнішим буде опис проблеми/запитання, тим легше буде іншим користувачам Dahle 508 надати вам вичерпну відповідь.

Ознайомтеся з безкоштовною інструкцією для Dahle 508. Ви ознайомились з інструкцією, але не змогли знайти відповідь на своє запитання? В такому випадку задайте своє запитання іншим користувачам продукції Dahle 508 на цій сторінці. Введіть ваше запитання тут

Характеристики продукту

Загальна інформація
Бренд Dahle
Модель 508
Продукт Бумагорізальна машина
EAN 4007885005089
Мова Англійська
Тип файлу PDF
Властивості
Довжина різки 317.5
Ріжуча здатність 7

інструкціїкористувача.com.ua

Шукаєте інструкцію? інструкціїкористувача.com.ua гарантує, що ви знайдете необхідне за лічені секунди. У нашій базі міститься більше 1 мільйона PDF-інструкцій від більш ніж 10 000 торгових марок. Щодня ми додаємо нові версії інструкцій, аби ви завжди могли знайти необхідну саме вам. Усе дуже просто: просто вкажіть назву торгової марки та тип продукції в рядку пошуку, i ви зможете безкоштовно та миттєво переглянути необхідну інструкцію.

інструкціїкористувача.com.ua

© Copyright 2020 інструкціїкористувача.com.ua. Усі права захищено.