GE Profile PKS7000BNTS

GE Profile PKS7000BNTS інструкція користувача

(1)
  • BEFORE YOU BEGIN
    Read these instructions completely and
    carefully.
    IMPORTANT Save these
    instructions for local inspector’s use.
    IMPORTANT Observe all
    governing codes and ordinances.
    Note to Installer – Be sure to leave these
    instructions with Consumer.
    Note to Consumer Keep these
    instructions for future reference.
    Skill level Installation of this appliance
    requires a qualified installer or electrician.
    Proper installation is the responsibility
    of the installer.
    Product failure due to improper installation
    is not covered under Warranty.
    Product is for indoor use only.
    Installation Instructions
    27” & 30” Electric Built-In Wall Ovens
    FOR YOUR SAFETY:
    WARNING
    Before beginning the installation, switch power off at the service panel and lock
    the service disconnecting means to prevent power from being switched on accidentally. When the
    service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a
    tag, to the service panel.
    Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight
    on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit,
    stand or hang on the oven door.
    Make sure the wall coverings, counters and cabinets around the oven can withstand the heat (up to
    200°F [93.3°C]) generated by the oven.
    MATERIALS YOU MAY NEED
    Junction Box
    Wire Nuts
    Strain Relief Clamp for 1/2” Conduit
    36” (91 cm) of String
    TOOLS YOU MAY NEED
    1/8” Drill Bit and Electric or Hand Drill
    T20 Screwdriver
    Phillips Screwdriver
    Wire Strippers
    7/16” Nut Driver (combination ovens)
    1/4” Nut Driver (30” combination ovens)
    1
    REMOVE PACKAGING MATERIALS
    Failure to remove packaging materials could result in damage to the appliance. Remove all
    packing parts from oven, racks and heating elements. Remove protective film and labels on
    the outer door and control panel. Also, remove plastic on trims and panel, all tape around the
    oven and any shipping screws securing the oven to the base pad. Open oven door and remove
    literature pack and oven racks. Remove the bottom trim from the top of the oven. It will be
    installed at the end of the installation process. The trim is wrapped separately and taped to the top
    of the unit. Remove pedestal rails from separate box and set aside (30” Double Wall Ovens Only).
    2
    PREPARE THE OPENING
    NOTE: If the cabinet does not have a solid
    bottom, two braces or runners must be
    installed to support the weight of the oven.
    For single ovens, the runners and braces
    must support 220 lbs (99 kg). For double and
    combination ovens, the runners and braces
    must support 400 lbs. (181 kg).
    NOTE: If marks, blemishes or the cutout
    opening are visible above the installed oven,
    it may be necessary to add wood shims
    under the runners until the marks or opening
    are covered.
    NOTE: If the cabinet does not have a front
    frame and the sides are less than ¾” (1.9 cm)
    thick, shim both sides equally to establish the
    cutout width.
    ATTENTION INSTALLER: All electric wall ovens must be hard-wired (direct-wired)
    into an approved junction box. A plug and receptacle is NOT permitted on these products.
    DESIGN INFORMATION
    SINGLE OVEN INSTALLATIONS
    The single oven may be installed in a cabinet alone or above a warming drawer. The single oven
    may also be installed side by side, below a countertop, or below specified cooktops. See the label
    on top of the oven for approved models.
    DOUBLE AND COMBINATION OVEN INSTALLATIONS
    A double or combination oven may be installed in a cabinet alone or above a warming drawer.
    See the label on top of the oven for approved models.
    IMPORTANT: Always refer to individual installation instructions packed with each product for
    specific requirements.
    Questions? Call us at 1.800.432.2737 or visit GEAppliances.com.
    In Canada, call 1.800.561.3344 or visit GEAppliances.ca.
    Suitable
    Bracing
    to Support
    Runners
    2" x 4" (5 cm x 10 cm)
    or Equivalent Runners Level
    with Bottom of Cutout
    and Flush with Sides of Cutout
    C
    L
GE Profile PKS7000BNTS

У вас виникло питання стосовно GE Profile PKS7000BNTS?

Кількість запитань: 0

Задайте запитання іншим користувачам GE Profile PKS7000BNTS. Надайте чіткий та вичерпний опис проблеми та свого запитання. Чим детальнішим буде опис проблеми/запитання, тим легше буде іншим користувачам GE Profile PKS7000BNTS надати вам вичерпну відповідь.

Ознайомтеся з безкоштовною інструкцією для GE Profile PKS7000BNTS. Ви ознайомились з інструкцією, але не змогли знайти відповідь на своє запитання? В такому випадку задайте своє запитання іншим користувачам продукції GE Profile PKS7000BNTS на цій сторінці. Введіть ваше запитання тут

Характеристики продукту

Загальна інформація
Бренд GE
Модель Profile PKS7000BNTS
Продукт Піч
Мова Англійська, Іспанська
Тип файлу PDF

інструкціїкористувача.com.ua

Шукаєте інструкцію? інструкціїкористувача.com.ua гарантує, що ви знайдете необхідне за лічені секунди. У нашій базі міститься більше 1 мільйона PDF-інструкцій від більш ніж 10 000 торгових марок. Щодня ми додаємо нові версії інструкцій, аби ви завжди могли знайти необхідну саме вам. Усе дуже просто: просто вкажіть назву торгової марки та тип продукції в рядку пошуку, i ви зможете безкоштовно та миттєво переглянути необхідну інструкцію.

інструкціїкористувача.com.ua

© Copyright 2020 інструкціїкористувача.com.ua. Усі права захищено.