Honeywell RTH230B інструкція користувача

Honeywell RTH230B
9.2 · 2
PDF інструкція користувача
 · 4 стор.
Англійська
інструкція користувачаHoneywell RTH230B
RTH230B 69-1800 2/6/05 1/4
The RTH230B programmable thermostat can be used to control:
a gas, fuel oil or electric furnace - 2 or 3 wires
a central air conditioner - 2 or 3 wires
a hot water system with or without pump - 2 wires
a millivolt system - 2 wires
a central heating and cooling system - 4 or 5 wires
Note: These thermostats are not compatible with heat pumps or
multi-stage systems.
Features
System operating mode selection: heat, cool or off
Fan operating mode selection: automatic or on (continuous)
Programmable heating and cooling cycle lengths: 10, 12, 15, 20
or 30 minutes
Temperature display in °F or °C
Battery replacement indicator
5-2 programming including:
- Preprogrammed energy-saving schedule
- Early Start
- Temporary bypass
- Time display (12 h or 24 h)
Filter replacement indicator

2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING SYSTEM.

n Remove the old thermostat to access the wires.

Warning: If the old thermostat was mounted onto an electrical box,
it was probably powered by 120/240 volts. In this case, this thermo-
stat cannot be used.
o Identify and label each wire (with the corresponding letter on
the wire terminal) and remove them from the terminals.

p If necessary, strip the end of each wire (maximum of 1/4 inch).

q Wrap the wires around a pencil to prevent

them from falling into the wall.

r If the hole in the wall is too big, insulate it

using a non-flammable material in order to
avoid air draughts behind the thermostat.

2.2 Installing the New Baseplate

For a new installation, choose a location approximately 5 feet
(1.5 m) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.

n Remove the thermostat faceplate.

o Loosen the locking screw to separate the thermostat from its

baseplate (the screw cannot be completely removed).

p Tilt the thermostat upwards.

q Mark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

r Pass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

2.3 Connecting the Thermostat

The connection of the new thermostat should be similar to that of
the old thermostat; however, it can vary depending on the installa-
tion.
Note: The red jumper wire between the Rc and Rh terminals must
be removed in 2- or 5-wire installations. The jumper must be used in
3- or 4-wire installations if you wish to use the mode selector switch
for the fan.

1. Introduction

2. Installation

RTH230B

Programmable Electronic Thermostat

Installation and User Guide

Display
Adjustment
buttons
System operating
mode selector
Fan operating
mode selector
Programming
buttons
Rh Heating power supply
Rc Cooling power supply
W Heating signal
Y Cooling signal
GFan

Ознайомтеся з безкоштовною інструкцією для Honeywell RTH230B. Ви ознайомились з інструкцією, але не змогли знайти відповідь на своє запитання? В такому випадку задайте своє запитання іншим користувачам продукції Honeywell RTH230B на цій сторінці. Введіть ваше запитання тут

У вас виникло питання стосовно Honeywell RTH230B?

У вас є запитання щодо Honeywell , а в посібнику немає відповіді?

  • Отримуйте оновлення щодо рішень
  • Отримуйте відповіді на своє запитання

Запитання та відповіді

Кількість запитань: 0

Honeywell RTH230B - це програмний термостат, який призначений для регулювання температури в будівлях. Його можна використовувати в будь-якому типі житла або робочого приміщення. Цей термостат підтримує складні програми, які дозволяють користувачам налаштовувати температуру в приміщенні відповідно до своїх потреб. Даний термостат має просте і інтуїтивно зрозуміле управління, що значно полегшує його використання навіть для людей без досвіду в області систем відопропомірної техніки. Крім того, Honeywell RTH230B імплементує технологію Adaptive Intelligent Recovery, що забезпечує автоматичне налаштування температури у кімнаті, а це означає, що у приміщенні буде завжди ідеальна температура. Окрім того, цей термостат сумісний з багатьма системами опалення, такими як: газові котли, електричні системи опалення, системи тепловентиляції, тощо. Завдяки вбудованому датчику температури, Honeywell RTH230B може підтримувати сталу температуру у приміщенні протягом цілого дня або ночі. Як і все програмне забезпечення, цей термостат також можна оновлювати та налаштовувати, що дає йому більшу гнучкість та ефективність у використанні.

Загальна інформація
БрендHoneywell
МодельRTH230B
Продукттермостат
МоваАнглійська
Тип файлуПосібник користувача (PDF)

Не можете знайти відповідь на своє запитання в посібнику? Ви можете знайти відповідь на своє запитання в розділі поширених запитань щодо Honeywell RTH230B нижче.

Де краще розташувати термостат?

Найкраще місце для термостата — це кімната, в якій ви проводите найбільше часу, у багатьох випадках це вітальня або кухня. Розташуйте термостат на висоті приблизно півтора метри над підлогою, не на сонці та не на зовнішній стіні.

Що таке мертва зона термостата?

Якщо термостат має мертву зону, ваша установка, так би мовити, «відпочиває». Термостат увімкнеться лише тоді, коли, наприклад, кімнатна температура відхилиться більше ніж на 2˚C від заданого значення.

Якою є ідеальна кімнатна температура?

Більшість людей вважає, що температура в приміщенні в діапазоні від 19 до 22 градусів за Цельсієм є ідеальною.

Чи доступний посібник для Honeywell RTH230B цією мовою: Український?

На жаль, у нас немає посібника для Honeywell RTH230B цією мовою: Український. Цей посібник доступний цією мовою: Англійська.

Ваше запитання відсутнє? Введіть ваше запитання тут

Немає результатів