Mobotix MX-BELL1-BUTTON-XL1 інструкція користувача

Mobotix MX-BELL1-BUTTON-XL1
9.2 · 1
PDF інструкція користувача
 · 2 стор.
Англійська
інструкція користувачаMobotix MX-BELL1-BUTTON-XL1
The HiRes Video Company
EN
www.mobotix.com
HiRes Video Innovations– Made in Germany
The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its decentralized concept has made high-resolution video
systems cost-ecient.
MOBOTIX AG • D-67722 Langmeil • Tel: +49 6302 9816-103 • Fax: +49 6302 9816-190 • sales@mobotix.com

BellRFID Quick Install

Bell Button Module with RFID Technology for up to Five PartiesModule for MOBOTIX IP Video Door Station, keyless entry and mailbox control, can be combined with the dierent bell button sets MX-Bell1-Button-F1/F2/F3/F4/05/XL1Free-of-charge printing service on
www.mobotix.com> Support
BellRFID base module with 1 admin and 5 user RFID cards
Interchangeable bell button sets (not included)
Integrated RFID technology for keyless entry
Available colors: white, silver, dark gray, black, amber
Usable with/without function button for mailbox control
Up to 60hrs backup power supply using DoorMaster (accessory)
Standard Connection: IP Video Door Station with BellRFID, InfoModule and DoorMasterInstallation and Initial Operation of the BellRFIDAvailable Bell Button Sets (for all color variants)
The BellRFID module is installed in the exactly
same manner as the KeypadRFID module. Make
sure that you follow the steps for the dierent
hardware scenarios of the IP Video Door Station
(with/without DoorMaster) as described in the
T24 System Manual Part1
for the KeypadRFID
(see below).
Note: BellRFID and KeypadRFID can only be used
on one MxBus with a later software version of
the camera.
MOBOTIX BellRFID
MX-Bell1-Core
(in IP Video Door Station
triple frame white)
I/O Terminal
Sealing plug
Seal
MxBus terminal
Back view with cover removed
Door
2
6
MxBus (YSTY 0.8 mm – max. length: 50m/55yd)
Theft protection (YSTY 0.8 mm – max. length: 50m/55yd)
Door opener, door sensor, lock sensor
(YSTY 0.8 mm – max. length: 50m/55yd)
DoorMaster
2
RFID cards
for keyless entry included
(1 admin card, 5 user cards)
MX-Bell1-Core
31.578_EN_V2_09/2013
You can use the blue function button at the door station to listen to new mailbox
messages, record new announcements and activate/deactivate the mailbox.
Visitors can leave a message even without the function button. The remaining
mailbox features are easily controlled using the remote station of the door
station (i.e., MOBOTIX App).
Each BellRFID base module contains 6 RFID cards (1admin, 5user cards).
Each button set contains pre-cut name plates made of UV-resistant paper. If
required, you can replace the button sets later on– in the same base module!
In order to configure the system using BellRFID, the bell buttons are replaced
by a keypad insert, which is delivered with the base module.
The Jones Family
MX-Bell1-Button-XL1
XL bell button
(no function button)
MX-Bell1-Button-F1
Large bell button
with function button
The Jones Family
MX-Bell1-Button-F2
2 medium-size bell buttons
with function button
The Jones
Family
Dr. Jones, MD
MX-Bell1-Button-F4
4 small bell buttons
with function button
Cindy JonesThomas JonesThe Jones FamilyDr. Jones, MD
MX-Bell1-Button-F3
1 large, 2 small bell buttons
with function button
Cindy JonesThomas JonesDr. Jones, MD
MX-Bell1-Button-05
5 small bell buttons
(no function button)
Caroline JonesCindy JonesThomas JonesThe Jones FamilyDr. Jones, MD
Before starting the installation and initial operation, you should download part 1 and 2 of the
T24 System Manual
from the MOBOTIX website
(www.mobotix.com> Support> Manuals).
If the installation of the IP Video Door Station with BellRFID is not followed by the initial operation right away, MOBOTIX recommends to remove the keypad
insert and to insert the button set before starting the installation. This way, the soft rubber surface of the BellRFID base module is well protected until the
module is brought into service (bell buttons are then replaced by the keypad insert). Note that the base module is weatherproof even without the bell
buttons.
When replacing the button set or exchanging name plates, you need to remove the module from the frame of the IP Video Door Station. Use the
blue MOBOTIX key for unlocking the module. Make sure that you are activating the mechanical theft protection with the red turning knob
in the door station frame only
after
you have finished the initial operation (see the
Section «Mechanical Anti-Theft Protection Lock»
in the
T24 System Manual Part1
).
In order to avoid having to remove the module and install it again, you should insert the proper name plates before starting the initial operation.
Use our free-of-charge printing service on www.mobotix.com in the Support section! Or use the supplied name plates made from sturdy specialty
paper and write the names using a UV-resistant marker.
Available Bell
Button Sets
(Accessory)
The Jones FamilyThe Jones FamilyDr. Jones, MDCindy JonesThomas JonesDr. Jones, MDCindy JonesThomas JonesThe Jones FamilyDr. Jones, MDCindy JonesThomas JonesThe Jones FamilyDr. Jones, MDCaroline JonesCindy JonesThomas JonesThe Jones FamilyDr. Jones, MDThe Jones Family
1. Insert the Name Plate(s)
Remove the silicon insert from the button. Recommendation: Take a suitable
tool without a sharp blade, cautiously insert it into the slot, gently press
inward and lift the tool as shown.
Insert the labeled or printed name plate as shown (the arrows at the side
are pointing upwards later on).
Place the silicon insert on top of the name plate, push it into the frame at
the top and at the bottom of the center, then push its sides into the frame.
Make sure that the silicon insert fits flush into the frame of the bell button
as shown to protect the name plate against humidity.
2. Insert the Module into the Door Station
You can use the BellRFID module as an alternative to the KeypadRFID (but
not yet side-by-side) in the frame of an IP Video Door Station. For installing
and wiring the module, follow the same steps as for the KeypadRFID.
Follow the description in the
Section «Installing the T24-KeypadRFID»
of the
T24 System Manual Part1
. Likewise, the other connection variants listed in
the
Section «Overview: Connection and Wiring Diagrams»
(e.g., connecting
an electrical door opener in a system without DoorMaster).
Finish the installation of the BellRFID module by following the steps listed
in the
Section «Finishing the Installation»
of the
T24 System Manual Part1
.
Similar to the KeypadRFID, the blue and the green status LEDs are flashing
(power supply OK, ready for auto configuration).
Installation Hint
When installing the module, insert it first on the right-hand
side. Then use two fingers and press on the left-hand
edge until the module clicks into the frame. Caution: Only
press at the edge, never at the center of the module!
Make sure that the cabling is not pinched and damaged
when installing the module.
3. Execute Auto Configuration
Place the supplied keypad insert into the base module
(push it into the frame at the top, then push the bottom
into the module).
Start the auto configuration of the IP Video Door Station by executing the
steps listed in the
Section «Step1: Performing the Auto Configuration»
of
the
T24 System Manual Part2
(connect all devices, establish the power
supply and press the bell button of the camera module immediately after
the light and bell buttons are lighting up).
Once you have successfully completed the auto configuration, the white
camera illumination is on and the BellRFID shows the following status:
The blue and the green status LEDs are flashing.
The LED of the keypad behind the top right key (OK) is red.
Finish the auto configuration by executing the steps listed in the
Section «Functional Test Part1»
of the
T24 System Manual Part2
.
4. Enter Super PIN and Confirm
The Super PIN is used to protect the system against misuse and also replaces
the factory default password (“meinsm”) as the new admin password. The
password is also used when adding the door station to the MOBOTIX App or
MxEasy, for example (user name is admin, new password is the <Super
PIN>). Select a Super PIN that has a minimum of 8 and a maximum of
16 digits (more and dierent digits make it more secure). For additional
information on the Super PIN, see the
T24 System Manual Part2
.
Dr.
D
r
.
J
o
n
e
s
,
M
D
1
3 4
2
1
2
Click!
Cindy Jones
Thomas Jones
The Jones Family
Dr. Jones, MD
IndoorOutdoor
For additional information on the other connection variants and for installing,
see the
T24 System Manual Part1
on www.mobotix.com > Support> Manuals.
IP Video Door Station
BellRFID
InfoModule
Cindy Jones
Thomas Jones
The Jones Family
Dr. Jones, MD
Use our free-of-charge Printing Service on www.mobotix.com, Support section!
Weatherproof (IP65)
–30 to +60°C/–22 to +140°F

Інструкція користувача

Ознайомтеся з безкоштовною інструкцією для Mobotix MX-BELL1-BUTTON-XL1. Ви ознайомились з інструкцією, але не змогли знайти відповідь на своє запитання? В такому випадку задайте своє запитання іншим користувачам продукції Mobotix MX-BELL1-BUTTON-XL1 на цій сторінці. Введіть ваше запитання тут

У вас виникло питання стосовно Mobotix MX-BELL1-BUTTON-XL1?

У вас є запитання щодо Mobotix MX-BELL1-BUTTON-XL1, а відповіді немає в посібнику? Введіть ваше запитання тут. Надайте чіткий і вичерпний опис проблеми та сформулюйте своє запитання. Що детальнішим буде опис проблеми/запитання, то легше буде іншим користувачам Mobotix MX-BELL1-BUTTON-XL1 надати вичерпну відповідь.

Кількість запитань: 0

Характеристики продукту

Нижче наведено технічні характеристики продукту та інструкції з експлуатації Mobotix MX-BELL1-BUTTON-XL1.

Загальна інформація
Бренд Mobotix
Модель MX-BELL1-BUTTON-XL1
Продукт Інше
EAN 4047438017169
Мова Англійська
Тип файлу Посібник користувача (PDF)
Технічні характеристики
Частота - кГц
Вбудований екран Ні
Колір продукту Сірий
Сертифікація IP65
Інтерфейс MxBus
Енергоживлення
Тип батарейок -
Зовнішні умови
Діапазон робочих температур -30 - 60 °C
показати більше

Поширені запитання

Не можете знайти відповідь на своє запитання в посібнику? Ви можете знайти відповідь на своє запитання в розділі поширених запитань щодо Mobotix MX-BELL1-BUTTON-XL1 нижче.

Ваше запитання відсутнє? Введіть ваше запитання тут

Немає результатів