Oregon Scientific BAA223PNH інструкція користувача
9.9 · 1
інструкція користувачаOregon Scientific BAA223PNH
EN
Thank you for selecting the Oregon Scientic™ Projection In/Out Thermo
Clock. This device bundles precise time keeping, alarm, and temperature
monitoring features into a single tool you can use from the convenience
of your home. Keep this manual handy as you use your new product.
It contains practical step-by-step instructions, as well as technical
specications and warnings you should know.
LCD Display
Weather
Forecast
Indicator
Indoor Temperature
Display
Outdoor Temperature
Display
Time Display
LCD Display
Symbol Description Function
Radio signal reception to
outdoor unit (RTHN129)
Indicates the strength of the
radio reception
Low battery
Indicates low battery power of
outdoor unit (RTHN129)
Alarm 1 on
Alarm 2 on
Appears when an alarm is
activated
RF antenna icon
Appears when RF clock data
received
OUT 12345
Outdoor sensor reading
Shows outdoor temperature of
selected sensor.
IN
Indoor sensor reading Shows indoor temperature
ZONE
Time zone Indicates selected time zone
Projection
NOTE
Focus length (1.5m – 2m)
Connecting the main unit to power supply
Connect the power cable to the Micro USB jack and plug the power
adaptor into a suitable power outlet.
Inserting batteries into remote thermo sensor
• Slide the battery compartment cover open and insert 2 “AAA” batteries,
matching the polarity as shown, then replace the cover.
• Press RESET inside the sensor after each battery change.
Placement of the main unit
Getting started - Line Drawing
Unpacking the product
Placement of the main unit
Connecting the main unit to power Inserting batteries into remote thermo sensor
Max 1.5m
Max 50m
• Place the device as far as possible from computers and microwaves to
avoid interference with reception.
• Only use this device indoors in a dry location.
• Leave space around the device for ventilation purposes, so that the
warm air can escape freely.
• To ensure for good sound quality, do not cover the speaker.
Placement of the remote thermo sensor (RTHN129)
Getting started - Line Drawing
Unpacking the product
Placement of the main unit
Connecting the main unit to power Inserting batteries into remote thermo sensor
• Ideal placements for the sensor would be in any location outside the
home at a height of not more than 5 ft (1.5 m), shielded from direct
sunlight or wet conditions.
NOTE
Depending on conditions, the maximum radio signal reach is 50 m.
Top
SNOOZE (Backlight / Projection) button
Temperature button Clock button
Set/Alarm button button
button
Micro USB jack Reset button
°C / °F button Light button
Flip 180° button
This product is designed to automatically synchronize its calendar and
clock when brought within the range of the radio signal. When the unit
is receiving the signal, the radio reception symbol (RCC) starts to blink.
Depending on the strength of the signal, the connection process takes
2 to 10 minutes. If the signal is weak, it could take up to 24 hours to
receive a valid signal.
The main unit is able to receive RF clock data from remote sensor in DCF
(EU) MSF (UK) and WWVB (US) format:
• DCF (EU) and MSF (UK): The time zone settings within the range of -23
to 23 reference to time zone 0 of the DCF/MSF broadcasting signal.
• WWVB (US): The time zone settings 0/1/2/3 reference to time zones
P/M/C/E of the WWVB broadcasting signal.
Clock signal reception indicator:
Symbol Description
Strong signal
Weak signal
No signal
Receiving signal
Radio reception disabled
NOTE
Reception can be affected by a number of factors. For best
reception, place the device away from metal objects and electrical
appliances. Other causes of signal interference include electrical
transmission towers, steel reinforced construction and metal siding.
Reception is ideal when the unit is placed near a window.
Enabling/disabling radio reception
SEARCH button (located inside the outdoor receiver)
• Press SEARCH to enable the RCC search function. The LED will ash
twice to indicate that search function is enabled.
• Press and hold SEARCH to disable the RCC search function. The LED will
ash three times to indicate that search function is disabled.
• Press and hold SEARCH (button is located inside the outdoor
receiver) to disable signal reception.
• Press and hold
. The screen displays ZONE and the number ashes.
• Press once or press and hold
and to adjust the setting. For EU/
UK, the time-zone offset sets the clock up to +/- 23 hours from the
received clock signal time. For US, the time-zone setting is 0(P), 1(M),
2(C), 3(E).
• Press
to conrm.
• Press once or press and hold
and to adjust the setting for 12/24h
hour format, hour, minute, year, calendar format (month-day/day-
month), month, date and temperature unit (°C/°F).
• Press
again to conrm.
• Press to toggle between time and date display.
You can set two different alarm times with this clock.
Setting/adjusting alarm time
• Press and hold
.
• Use
and to adjust the hour and press to conrm.
• Use
and to adjust the minute and press to conrm.
• The alarm time is displayed. The alarm sound will stop after 2 minutes.
Snooze function
• To use the SNOOZE function, press the SNOOZE (light) button on
top of the clock when the alarm sounds. The alarm will stop and start
again after 8 minutes. You can repeat this function three times.
Displaying the alarm time
By default the clock will show the current time and date.
• To display Alarm 1 for 5 sec, press
and .
• To display Alarm 2 for 5 sec, press
and .
Activating/deactivating the alarm
• Press
to activate/deactivate alarm in sequence:
Alarm1 > Alarm 2 > Both ON > Both OFF.
• Press the Light button to toggle the desired backlight display
brightness level.
• To activate the projection and the brightest backlight display for 5
seconds, press the Snooze (light) button.
The projector displays the time on your ceiling for easy viewing in a
darkened room.
• To activate the backlight and projection function for 5 seconds, press
the SNOOZE (light) button.
NOTE
This function only works when the projection function is turned OFF.
• To turn projection ON and OFF press and hold Light to toggle
between options. (The default setting is ON)
• To ip the projection content by 180°, press Flip 180°.
The temperature is measured in °C or °F.
• Press °C / °F to toggle between Centigrade (°C) and Fahrenheit (°F).
The current indoor temperature is always displayed in the lower right
corner of the LCD display. To receive outdoor temperature information, you
can connect up to 5 remote sensors to the main unit:
• Press
& to toggle between channels (1 to 5) and display the
outdoor temperature of different sensors.
• Press and hold
and for 2 seconds to start searching for remote sensors.
• Press and hold and for 2 seconds to enable auto-scan function for
the 5 channels. Information from Channel 1,2,3,4,5 will automatically
be displayed in sequence.
Whenever the clock is not behaving as expected, press Reset with the
point of a blunt object such as a stylus or ball point pen.
NOTE
This will return all settings to default values.
The main unit can collect temperature data from up to 5 sensors, and
should be placed within 98 ft (50 m) of the main unit. The amber LED
Indicator on the front of the sensor will blink to indicate that the unit is
transmitting a signal.
s
CH Channel 1-5. If more than one sensor is being used, make sure
each one has a different channel number.
EU/UK/US: Select your region for RCC.
SEARCH Press to search for RCC function.
RESET Press if the sensor is not working correctly or if the batteries
have been replaced.
NOTE
Before placing the remote sensor outdoors, check that the battery
compartment door is closed properly,
MAIN UNIT
BAA223PNH
REMOTE THERMO SENSOR (RTHN129)
Please observe the following safety precautions when setting up and
using this product.
• The manufacturer assumes no liability for possible damages that may
have been caused by incorrect usage or mishandling of the device.
• Prior to using the device for the rst time, check to make sure that
your household power supply corresponds to the voltage listed on
the device.
• LCD panel - The LCD panel is made of glass and may break if the unit
is dropped or impacted.
• Heat sources - Keep the product away from heat sources such as
radiators, stoves, heaters and other heat-generating products.
• Water and moisture - Do not use the unit in or near water or in high
moisture areas such as bathrooms.
• Power cord - If the power cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualied persons in
order to avoid a hazard.
• Repair - Do not attempt to repair or modify the unit yourself.
Contact the retailer or a qualied repairman if the product requires
servicing. Only use replacement parts that are recommended by the
manufacturer.
• Danger of suffocation! Keep all packaging material away from children.
CARE
This product is designed to give you years of service if handled properly.
Oregon Scientic will not be responsible for any deviations in the usage of
the device from those specied in the user instructions or any unapproved
alterations or repairs of the product. Observe the following guidelines:
• Attention!
Before cleaning disconnect the power plug from the socket.
• Cleaning - Use a damp cloth to wipe the unit. Do not use liquid
cleaning agents, benzene, thinner or aerosols.
• Projector lens - A dirty lens can result in a blurred projection. From time
to time, check to see if dust or other dirt has collected on the lens. Dust:
blow the dust from the lens with a brush/blower made for cameras
(available at an authorised dealer). After that, brush the lens lightly with
the brush and then blow dust off the lens again.
Fingerprints: If the lens does not become clean by using the brush/
blower, use a cotton swab, dipped in a special cleaning solution and
remove the dirt beginning from the middle and proceeding to the outside.
• Do not scratch the LCD display with hard objects.
• Never immerse the product in water. This can cause electrical shock
and damage the product.
• Do not subject the main unit to extreme force, shock, or uctuations in
temperature or humidity.
• Do not tamper with the internal components.
• Ventilation - The vents and other openings are designed to keep the
unit cool and should not be blocked or covered. Preventing ventilation
can lead to overheating and may damage the unit.
• Do not expose batteries to extreme heat like direct sunlight, re, etc.
• Batteries do not belong in household waste! Expired batteries must
be disposed of in an environmentally friendly way and according to
the applicable legal regulations.
• Batteries are very dangerous if swallowed. Please keep expired
batteries away from children at all times. If a battery is swallowed,
seek medical attention immediately.
• Batteries must not be recharged or activated with another means,
dismantled, thrown into re or short-circuited.
• Do not mix new and old batteries or batteries of different types.
• Do not use rechargeable batteries with this product.
• Remove the batteries if storing this product for a long period of time.
• The batteries must be removed prior to disposing of the device.
NOTE
The technical specication of this product and contents of this user
guide are subject to change without notice. Images not drawn to scale.
Visit our website www.oregonscientic.com to learn more about
Oregon Scientic products.
For any enquiry, please contact our Customer Services at
info@oregonscientific.com.
Oregon Scientic Global Distribution Limited reserves the right to interpret
and construe any contents, terms and provisions in this user manual and
to amend it, at its sole discretion, at any time without prior notice. To the
extent that there is any inconsistency between the English version and
any other language versions, the English version shall prevail.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Changes or modications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the nterference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.
The following information is not to be used as contact for support or sales.
Please call our customer service number
(listed on our website at www.oregonscientic.com),
or on the warranty card for this product for all inquiries instead.
We
Name: Oregon Scientic, Inc.
Address: 10778 SW Manhasset Dr.
UNIT B-2 Tualatin,
OR 97062 USA
Telephone No.: 1-800-853-8883
declare that the product
Product No.: BAA223PNH
Product Name: Projection Clock
Manufacturer: IDT Technology Limited
Address: Block C, 9/F, Kaiser Estate,
Phase 1, 41 Man Yue St.,
Hung Hom, Kowloon, Hong Kong
is in conformity with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: 1) This device may not cause harmful
interference. 2) This device must accept any interference received,
including interference that may cause undesired operation.
Hereby, Oregon Scientic, declares that this Projection Clock
(Model: BAA223PNH) is in compliance with EMC directive 1999/5/
EC. A copy of the signed and dated Declaration of Conformity is
available on request via our Oregon Scientic Customer Service.
SC
产品描述
TM
产品简介
天气预报
显示
电量不足
调频图标
OUT
IN
ZONE
投影器
显示时间
注意:
开始使用
插座中。
注
顶部
背面
温度按钮 时钟按钮
设置/闹钟按钮 按钮
Micro USB 插头 重置按钮
°C/°F按钮 灯光按钮
着亮起
强讯号
弱讯号
•
注
于窗边。
及 来调整设置。对于欧洲/英国，时区偏移会从
• 按
及 来调教 12/24 小时格式、小时、分钟、年份、
闹钟功能
.
及 来调教小时并按 来确定。
及 来调教分钟并按 来确定。
• 按
背面灯
Інструкція користувача
Ознайомтеся з безкоштовною інструкцією для Oregon Scientific BAA223PNH. Ви ознайомились з інструкцією, але не змогли знайти відповідь на своє запитання? В такому випадку задайте своє запитання іншим користувачам продукції Oregon Scientific BAA223PNH на цій сторінці. Введіть ваше запитання тут
Характеристики продукту
Нижче наведено технічні характеристики продукту та інструкції з експлуатації Oregon Scientific BAA223PNH.
Загальна інформація
| Бренд | Oregon Scientific |
| Модель | BAA223PNH |
| Продукт | Метеорологічна станція |
| Мова | Англійська |
| Тип файлу | Посібник користувача (PDF) |
Поширені запитання
Не можете знайти відповідь на своє запитання в посібнику? Ви можете знайти відповідь на своє запитання в розділі поширених запитань щодо Oregon Scientific BAA223PNH нижче.
Акумулятор Метеорологічна станція почав кородувати. Чи є цей пристрій безпечним для використання?
Після належного очищення продукт можна безпечно використовувати. Надягніть рукавички, вийміть акумулятор і очистьте акумуляторний відсік зубною щіткою, змоченою оцтом. Після висихання в пристрій можна вставити нові акумулятори.
Чи доступний посібник для Oregon Scientific BAA223PNH цією мовою: Український?
На жаль, у нас немає посібника для Oregon Scientific BAA223PNH цією мовою: Український. Цей посібник доступний цією мовою: Англійська.
Ваше запитання відсутнє? Введіть ваше запитання тут
Немає результатів
У вас виникло питання стосовно Oregon Scientific BAA223PNH?
У вас є запитання щодо Oregon Scientific BAA223PNH, а відповіді немає в посібнику? Введіть ваше запитання тут. Надайте чіткий і вичерпний опис проблеми та сформулюйте своє запитання. Що детальнішим буде опис проблеми/запитання, то легше буде іншим користувачам Oregon Scientific BAA223PNH надати вичерпну відповідь.
Кількість запитань: 0