Sony MDR-RF4000K

Sony MDR-RF4000K інструкція користувача

(1)
  • 4 Insert the headphones in the transmitter so that
    the headphones’ contact point meets the
    transmitter’s contact pin, and make sure that the
    CHG indicator lights up.
    It takes approximate 16 hours to fully charge the battery
    (the CHG indicator goes off when charging is complete.)
    When placing the headphones on the transmitter, be
    sure to insert the left and right housings completely.
    When the transmitter’s contact pin meets the
    headphones’ contact point, the CHG indicator lights up
    in red.
    If the CHG indicator is not lit
    Be sure to close the battery compartment lid. The battery
    charge function is not activated when the lid is not fully
    closed.
    Check that the left and right headphones are inserted in
    the transmitter correctly.
    The indicator will not light up if the headphones’ contact
    point does not meet the transmitters contact pin. In this
    case, remove the headphones and insert them in the
    transmitter again so that the indicator lights up.
    Make sure that the supplied rechargeable nickel-metal
    hydride battery is installed in the battery compartment.
    You cannot charge any rechargeable battery or dry-cell
    battery other than the supplied battery.
    To recharge the headphone battery after use
    Place the headphones on the transmitter after use. The CHG
    indicator lights up, and then charging starts.
    Since the built-in timer recognizes when charging is
    complete, there is no need to remove the headphones from
    the transmitter after charging has completed.
    Notes
    The transmitter automatically turns off while charging the battery.
    This system is designed to charge only the supplied rechargeable
    battery, type BP-HP550-11, for safety. Note that other types of
    rechargeable battery cannot be charged with this system.
    You cannot charge any rechargeable battery or dry-cell battery
    other than the supplied battery.
    Do not attempt to use the supplied BP-HP550-11 rechargeable
    battery with other components. It is for use with this system only.
    Charge in an environmental temperature of between 0 °C and 40 °C
    (between 32 °F and 104 °F). Otherwise, the battery may not be fully
    charged.
    Do not touch the contact pin of the transmitter. If a contact pin
    becomes dirty, charging may not be possible.
    Charging may not be completed if the transmitter’s contact pin and
    headphones’ contact point are dusty. Wipe them with a cotton bud,
    etc.
    Charging and usage time
    Approx. charging time Approx. usage time*
    1
    16 hours*
    2
    7 hours*
    3
    *
    1
    at 1 kHz, 1 mW + 1 mW output
    *
    2
    hours required to fully charge an empty battery
    *
    3
    Time may vary, depending on the temperature or conditions of
    use.
    Checking the remaining
    battery power
    Pull up the self-adjusting band and check the POWER
    indicator located on the right housing. The battery is still
    serviceable when the indicator lights in green.
    Charge the rechargeable battery or install new dry-cell
    batteries if the POWER indicator light dims, flashes, or the
    sound becomes distorted or noisy.
    Note
    The rechargeable nickel-metal hydride battery should be replaced
    with a new one when it lasts only half the expected time, after a full
    charge has been performed. The rechargeable battery, type BP-
    HP550-11, is not commercially available. You can order the battery
    from the store where you purchased this system, or at your nearest
    Sony dealer.
    Using the headphones with
    alkaline batteries (sold
    separately)
    Commercially available (size AAA) alkaline batteries can
    also be used to power the headphones. Install the batteries
    in the same manner as described in “Inserting the supplied
    rechargeable nickel-metal hydride battery.
    When dry-cell batteries are installed, the battery charge
    function is not activated.
    Battery life
    Battery Approx. hours*
    1
    Sony alkaline batteries
    LR03/AM-4(N)
    10 hours*
    2
    *
    1
    at 1 kHz, 1 mW + 1 mW output
    *
    2
    Time may vary, depending on the temperature or conditions of
    use.
    Notes on Batteries
    Do not charge a dry-cell battery.
    Do not carry a dry-cell battery together with coins or other metallic
    objects. Heat can be generated by the battery if its positive and
    negative terminals are accidentally shorted.
    If you are not going to use the unit for a long time, remove the
    batteries to avoid damage from battery leakage or corrosion.
    Welcome!
    Thank you for purchasing the Sony MDR-RF4000K Wireless
    Stereo Headphone System. Before operating the unit, please
    read this manual thoroughly and retain it for future
    reference.
    Some features are:
    Wireless stereo headphone system for music and movies
    2.4 GHz digital transmission with high quality sound
    Impressive sound reproduction with 40 mm driver unit
    equipped high quality closed type headphones
    2 way transmitter design for convenient setting
    Easy battery charging system
    Lightweight headphones for long time listening comfort
    Real-time automatic tuning on headphones for best
    reception of signal
    Up to 30 meters reception range*
    7 hours playback with supplied Ni-MH rechargeable
    battery
    Easy connection with TV/DVD/audio equipment with
    supplied audio cable
    Automatic On/Off function on headphones to preserve
    battery life
    Free adjustable headband for precise and comfortable fit
    Volume control function on the headphones
    * Transmission distance varies depending on conditions of use.
    Preparation
    Checking the components and
    accessories
    Before setting up the system, check that all of the
    components are included.
    Transmitter TMR-RF4000 (1)
    Wireless stereo headphones MDR-RF4000 (1)
    Wireless Stereo
    Headphone System
    3 Put on the headphones.
    When you put on the headphones, the headphones
    power turns on automatically.
    The POWER indicator on the right housing lights up. Be
    sure to put the right housing on your right ear and
    the left housing on your left ear. Wear the
    headphones vertically on your head so that auto power
    on function is properly activated.
    There is a tactile dot on the hanger marked to
    distinguish the left side.
    Tactile dot
    (on the left)
    4 Adjust the volume.
    Volume control
    Notes
    When watching films, be careful not to raise the volume too
    high in quiet scenes. You may hurt your ears when a loud scene
    is played.
    You may hear some noise when you disconnect the AC power
    adaptor from the transmitter before removing the headphones.
    RF signal transmission area
    The approximate RF signal transmission area from the
    transmitter is up to 30 m (100 ft).
    The transmitter detects the optimum frequency
    automatically when the headphones are removed from the
    transmitter. The sound may be interrupted if the
    headphones are out of RF signal transmission area or
    reception conditions deteriorate. In this case, move closer to
    the transmitter.
    Notes
    Because this system transmits signals at 2.4 GHz, sound may be
    interrupted if interference occurs. This is due to radio frequency
    characteristics, and is not a malfunction.
    Any noise you hear through the headphones may vary depending
    on the transmitter position and room conditions. It is
    recommended that you place the transmitter in a location that
    produces the clearest sound.
    Sound may be interrupted if the transmitter is used with other
    wireless apparatus using 2.4 GHz frequency, or a microwave oven.
    If an audio signal is not input for 10 minutes
    RF signal transmission from the transmitter automatically
    stops when an audio signal is not input for 10 minutes.
    When the transmitter stops, the transmitter’s POWER
    indicator blinks in green for 30 seconds and then turns off.
    The RF signals are automatically transmitted when an audio
    signal is input again. RF signal transmission may stop when
    an extremely low sound is input for about 10 minutes. If this
    happens, raise the volume of the connected AV component
    and lower the volume of the headphones. If signal noise is
    output from a component connected to the PHONES IN
    jacks, RF signal transmission may not stop.
    The headphones automatically turn off when
    they are removed
    — Auto Power On/Off function
    Do not pull up the self-adjusting band when not in use, as
    this will consume the battery power.
    Self-adjusting
    band
    Replacing the earpads
    The earpads are replaceable. If the earpads become dirty or
    worn out, replace them as illustrated below. The earpads are
    not commercially available. You can order replacements
    from the store where you purchased this system, or at your
    nearest Sony dealer.
    1 Remove the old earpad by pulling it off.
    2 Place the new earpad around the housing.
    ©2010 Sony Corporation Printed in China
    MDR-RF4000K
    4-170-882-65(1)
    AC power adaptor (1)
    Rechargeable nickel-metal hydride battery BP-HP550-11 (1)
    Connecting cable (stereo mini plug
    pin plug × 2),
    1 m (39
    3
    /
    8
    in) (1)
    Unimatch plug adaptor (stereo mini jack
    stereo phone
    plug) (1)
    Stand (1)
    Inserting the supplied
    rechargeable nickel-metal
    hydride battery
    The supplied rechargeable nickel-metal hydride battery is
    not charged from the first time you use it. Be sure to charge
    it before use.
    To charge the headphones, place them on the transmitter.
    1 Press the PUSH button of the left housing to open
    the battery compartment lid.
    The battery compartment lid comes off.
    PUSH button
    2 Insert the supplied rechargeable nickel-metal
    hydride battery into the battery compartment,
    matching
    terminal on the battery to the
    mark
    in the compartment.
    Do not attempt to charge any other kind of battery with
    this unit.
    Note
    The battery compartment has a tab on the
    side which holds the
    rechargeable battery in place. Insert the
    terminal first when
    installing the rechargeable battery.
    3 Close the battery compartment lid.
    Insert the tab in the hole at the top left.
    Close the lid until it clicks.
    English
    WARNING
    To reduce the risk of fire or electric shock, do not
    expose this apparatus to rain or moisture.
    To avoid electrical shock, do not open the cabinet. Refer
    servicing to qualified personnel only.
    For the customers in the Canada
    This Class B digital apparatus complies with Canadian
    ICES-003.
    Operation is subject to the following two conditions: (1) this
    device may not cause interference, and (2) this device must
    accept any interference, including interference that may
    cause undesired operation of the device.
    This Transmitter complies with IC radiation exposure limits
    set forth for uncontrolled equipment and meets RSS-102 of
    the IC radio frequency (RF) Exposure rules. This equipment
    has very low levels of RF energy that it deemed to comply
    without maximum permissive exposure evaluation (MPE).
    This Transmitter is desirable that it should be installed and
    operated with at least 20 cm and more between the radiator
    and persons body (excluding extremities: hands, wrists, feet
    and ankles).
    This Wireless stereo headphones complies with IC radiation
    exposure limits set forth for uncontrolled equipment and
    meets RSS-102 of the IC radio frequency (RF) Exposure
    rules. This Wireless stereo headphones has very low levels of
    RF energy that it is deemed to comply without testing of
    specific absorption ratio (SAR).
    For the customers in the Canada
    RECYCLING NICKEL METAL HYDRIDE
    BATTERIES
    Nickel Metal Hydride batteries are
    recyclable.
    You can help preserve our environment
    by returning your used rechargeable
    batteries to the collection and recycling
    location nearest you.
    For more information regarding recycling of
    rechargeable batteries, call toll free
    1-800-822-8837, or visit http://www.rbrc.org/
    Caution: Do not handle damaged or leaking Nickel
    Metal Hydride batteries.
    Connection
    Setting up the transmitter
    1 Connect the transmitter to an AV component.
    Select one of the hookups below depending on the jack
    type:
    To connect to a headphones jack
    Transmitter
    Left channel
    (white)
    Right channel
    (red)
    To PHONES IN jacks
    Connecting cord
    (supplied)
    Unimatch plug
    adaptor (supplied)
    To headphones
    jack (Stereo
    phone jack)
    To headphones jack
    (Stereo mini jack)
    WALKMAN®*,
    TV, etc.
    To connect to LINE OUT or REC OUT jack
    Transmitter
    To LINE IN jack
    Right channel (red)
    Connecting cord
    (supplied)
    Stereo system,
    VCR, etc.
    To LINE OUT or
    REC OUT jacks
    Left channel (white)
    * “WALKMAN” and “WALKMAN” logo are registered trademarks
    of Sony Corporation.
    Operation
    Listening to a programme
    Before listening
    To reduce the risk of hearing damage, first lower the volume.
    1 Turn on the AV component connected to the
    transmitter.
    If the transmitter is connected to the headphone jack, set
    the volume control of the audio source component as
    high possible but not so high that the audio signal
    becomes distorted.
    2 Remove the headphones from the transmitter.
    The transmitter’s POWER indicator lights up in green.
    Charging
    1 Connect the supplied AC power adaptor to the
    transmitter.
    Transmitter
    AC power adaptor
    (supplied)
    To an AC outlet
    To DC IN
    5.2 V jack
    Notes
    Be sure to use the supplied AC power adaptor. Using AC
    adaptors with different plug polarity or other characteristics
    can cause product failure.
    Unified polarity plug
    Be sure to always use the supplied AC power adaptor. Even AC
    power adaptors having the same voltage and plug polarity can
    damage this product due to the current capacity or other
    factors.
    Connect the AC power adaptor to an easily accessible AC
    outlet. Should you notice an abnormality in the AC power
    adaptor, disconnect it from the AC outlet immediately.
    2 Put the stand to the transmitter.
    You can place the transmitter horizontally or vertically,
    using the stand.
    Notes on the transmitter with stand and
    installation surface
    The stand should not be placed on a surface that is cloth-
    covered, textured, dirty or dusty.
    Peel off the protection films (transparent) on the adhesive
    sheets (4 corners) of the stand. The stand cannot be
    installed with the protection films on the adhesive sheets.
    When placing the transmitter, press it down softly to
    steady the stand.
    If the power of the adhesive sheets becomes
    weak
    Use a soft cloth slightly moistened to remove dust. A soft
    cloth with mild detergent solution may be used to remove
    finger marks or grease. The power of the adhesive sheets will
    be restored for repeated use.
    To change the installation place
    Move the stand slowly with your fingers on the edge of the
    stand. The adhesive sheets will not be detached with a sharp
    move.
    3 Turn the left and right headphones so as to be flat.
    Additional information
    Troubleshooting
    If you run into any problems using this headphone system,
    use the following checklist. Should any problem persist,
    consult your nearest Sony dealer.
    No sound
    Check the connection between the transmitter and the AV
    component.
    Turn on the AV component connected to the transmitter, and
    start the playback.
    If you connect the transmitter to an AV component using the
    headphone jack, raise the volume level on the connected AV
    component.
    Make sure you are wearing the headphones correctly.
    Raise the headphone volume.
    The headphones’ POWER indicator goes off.
    Charge the rechargeable battery if it is weak, or replace alkaline
    batteries with new ones. If the POWER indicator is still off
    after charging the battery, take the headphones to a Sony
    dealer.
    Distorted or intermittent sound
    (sometimes with noise)
    Charge the rechargeable battery if it is weak, or replace alkaline
    batteries with new ones. If the POWER indicator is still off after
    charging the battery, take the headphones to a Sony dealer.
    Check if there is any wireless apparatus using 2.4 GHz frequency,
    or a microwave oven in the vicinity.
    Change the position of the transmitter.
    If you connect the transmitter to an AV component using the
    headphone jack, lower the volume level on the connected AV
    component.
    Low sound
    If you connect the transmitter to an AV component using the
    headphone jack, raise the volume level on the connected AV
    component.
    Raise the headphone volume.
    Loud background noise
    Check if there is any wireless apparatus using 2.4 GHz frequency,
    or a microwave oven in the vicinity.
    If you connect the transmitter to an AV component using the
    headphone jack, raise the volume level on the connected AV
    component.
    Charge the rechargeable battery if it is weak, or replace alkaline
    batteries with new ones. If the POWER indicator is still off after
    charging the battery, take the headphones to a Sony dealer.
    The sound cuts off
    The transmitter stops transmitting if no signal is input for 10
    minutes.
    If you connect the transmitter to an AV component using the
    headphone jack, raise the volume level on the connected AV
    component.
    The battery cannot be charged
    Check if the CHG indicator turns on. If not, put the headphones
    on the transmitter correctly so that the CHG indicator turns on.
    Dry batteries are installed.
    Insert the supplied rechargeable nickel-metal hydride battery.
    Rechargeable batteries other than the supplied are installed.
    Insert the supplied rechargeable nickel-metal hydride battery.
    The transmitter’s contact pin and headphones’ contact point are
    dusty.
    Wipe them with a cotton bud, etc.
    A repeated beep sounds.
    The headphones cannot receive the signal from the transmitter.
    Move within the RF signal transmission area.
    Check the connection of the transmitter, AC power adaptor,
    and AC outlet.
    Check if there is any wireless apparatus using 2.4 GHz
    frequency, or a microwave oven around the transmitter and
    headphones.
    Change the position of the transmitter.
    There is no audio signal input for about 10 minutes and RF
    signals are not transmitted.
    Input the audio signal to the transmitter.
    The unit does not operate properly.
    Reset the system.
    Push a small pin, etc., into the hole of the transmitter until you
    feel a click.
    The POWER indicator on top starts blinking in green.
    Once the POWER indicator starts blinking, pull up and hold
    the self-adjusting band to turn on the headphones, and push a
    small pin, etc., into the hole of the right headphone until you
    feel a click.
    The POWER indicator of the transmitter stops blinking and
    stays lit in green.
    Precautions
    On safety
    Do not drop, hit, or otherwise expose the headphones to
    strong shock of any kind. This could damage the product.
    Do not disassemble or attempt to open any parts of the
    system.
    On power sources and placement
    If you are not going to use the system for a long time,
    unplug the AC power adaptor from the AC outlet. When
    removing the plug, grip the AC power adaptor.
    Do not pull on the cord.
    Do not place the system in any of the following locations.
    – Location exposed to direct sunlight, near a heater, or
    other extremely high-temperature location
    – Dusty location
    – On an unsteady or inclined surface
    – Location exposed to large amounts of vibration
    – Bathroom or other high-humidity locations
    On headphones
    Act considerately
    When the volume is too high, the sound leaks outside the
    headphones. Be careful not to raise the volume so high that
    it bothers people around you.
    There is a tendency to raise the volume when using in noisy
    places. However, for reasons of safety, it is advised to keep
    the volume at a level whereby you can still hear sounds
    around you.
    On cleaning
    Use a soft cloth slightly moistened with mild detergent
    solution. Do not use solvents such as thinner, benzene or
    alcohol as these may damage the surface.
    When the product breaks
    When the product breaks, or if a foreign object gets inside
    the unit, immediately turn off the power and consult your
    nearest Sony dealer.
    When taking the system to a Sony dealer, be sure to take
    both the headphones and transmitter.
    Specifications
    Wireless stereo transmitter (TMR-RF4000)
    Modulation System
    GFSK
    Carrier wave frequency
    2.404 GHz - 2.476 GHz
    Transmission distance
    Approx. 30 m (100 ft) of longest
    Frequency response
    10 Hz - 22,000 Hz
    Distortion rate
    1% or less (1 kHz)
    Audio inputs
    Phono jacks (left/right)
    Stereo mini jack
    Power requirements
    DC 5.2 V (from the supplied AC power adaptor)
    Dimensions
    Approx. 246 mm × 75 mm × 120 mm
    (9
    3
    /
    4
    in × 3 in × 4
    3
    /
    4
    in) (w/h/d)
    Mass Approx. 430 g (15.2 oz)
    Wireless stereo headphones (MDR-RF4000)
    Playback frequency range
    12 Hz – 22,000 Hz
    Power requirements
    Rechargeable nickel-metal hydride battery
    (supplied) or commercially available (size AAA)
    alkaline batteries
    Mass Approx. 300 g (10.6 oz) (including the supplied
    rechargeable nickel-metal hydride battery)
    Supplied accessories
    AC power adaptor (5.2 V) (1)
    Rechargeable nickel-metal hydride battery
    BP-HP550-11 (550 mAh) (1)
    Connecting cable (stereo mini plug
    pin
    plug × 2), 1 m (39
    3
    /
    8
    in) (1)
    Unimatch plug adaptor (stereo mini jack
    stereo phone plug) (1)
    Stand (1)
    Card warranty (1)
    Operating Instructions (this manual) (1)
    Design and specifications are subject to change without
    notice.
    Operating Instructions
    Mode d’emploi
Sony MDR-RF4000K

У вас виникло питання стосовно Sony MDR-RF4000K?

Кількість запитань: 0

Задайте запитання іншим користувачам Sony MDR-RF4000K. Надайте чіткий та вичерпний опис проблеми та свого запитання. Чим детальнішим буде опис проблеми/запитання, тим легше буде іншим користувачам Sony MDR-RF4000K надати вам вичерпну відповідь.

Ознайомтеся з безкоштовною інструкцією для Sony MDR-RF4000K. Ви ознайомились з інструкцією, але не змогли знайти відповідь на своє запитання? В такому випадку задайте своє запитання іншим користувачам продукції Sony MDR-RF4000K на цій сторінці. Введіть ваше запитання тут

Характеристики продукту

Загальна інформація
Бренд Sony
Модель MDR-RF4000K
Продукт Навушник
EAN 4905524615937, 0027242783591, 4905524632477
Мова Англійська, Французький
Тип файлу PDF
- Повнорозмірні
- Наголов'я
- 10 - 22000
- 1
- 40
- Dynamic
- Neodymium
- Зачинений
- Бездротовий
- 30
- 2.4
- 8
- Нікель-метал-гідридний (NiMH)
- 2
- AAA
- Чорний
-
-
Батарея
Час роботи батареї (макс) 8
Технологія батареї Нікель-метал-гідридний (NiMH)
Тип батарейок AAA
Кількість батарей 2
Навушники
Юніт динаміка 40
Тип магніту Neodymium
Сумарний коефіціент гармонік (THD) 1
Акустична система Зачинений
Тип драйверу Dynamic
Частота навушників 10 - 22000
Тип навушників Повнорозмірні
Порти та інтерфейси
Смуга частот 2.4
Дальність дії (бездротова) 30
Технологія підключення Бездротовий
Радіочастотне з’єднання
Характеристики
Колір продукту Чорний
Стиль носіння Наголов'я
Тип продукту

інструкціїкористувача.com.ua

Шукаєте інструкцію? інструкціїкористувача.com.ua гарантує, що ви знайдете необхідне за лічені секунди. У нашій базі міститься більше 1 мільйона PDF-інструкцій від більш ніж 10 000 торгових марок. Щодня ми додаємо нові версії інструкцій, аби ви завжди могли знайти необхідну саме вам. Усе дуже просто: просто вкажіть назву торгової марки та тип продукції в рядку пошуку, i ви зможете безкоштовно та миттєво переглянути необхідну інструкцію.

інструкціїкористувача.com.ua

© Copyright 2020 інструкціїкористувача.com.ua. Усі права захищено.